Roof measurement software

Measure roofs on satellite imagery without leaving your estimating workflow.

Trace roof planes, classify edges, record pitch, review calculated geometry, and carry the approved measurements into material takeoffs and estimates.

Own the geometry

Keep editable roof planes, edges, pitch, and penetrations attached to the property record.

Review before pricing

Inspect the measurement summary before quantities and prices enter an estimate.

One connected record

Move from address to measurement, estimate, proposal, and job without re-keying the property.

How it works

  1. 1

    Start from the address

    Create the property once. The measurement, estimate, proposal and job all hang off the same record.

  2. 2

    Trace each roof plane

    Draw the planes on third-party satellite imagery. You decide where every edge goes; nothing is guessed for you.

  3. 3

    Classify edges and set pitch

    Mark ridges, hips, valleys, eaves and rakes, and record the pitch of each plane so sloped area is calculated, not eyeballed.

  4. 4

    Review the totals

    Check sloped area, squares and linear feet by edge type, plus penetrations, before anything is priced.

  5. 5

    Price it

    Send the approved measurement into an estimate, where your assemblies and price book turn it into material quantities and cost.

  6. 6

    Show the homeowner

    Frame the roof image with classified edges, dimensions and pitch, and include it in the proposal.

A deliberate measurement workflow

MeasureRoofNow currently uses manual tracing on available satellite imagery. That makes the operator—not an unreviewed detection model—the final decision maker.

Manual tracing takes more of your time than a report that arrives finished, but you see every line that will drive the order, and you can fix a wrong edge before it becomes a wrong material list. Experienced estimators often prefer that trade on roofs they will be held to.

  • Draw each roof plane
  • Classify ridges, hips, valleys, eaves, and rakes
  • Set pitch and review area and linear-foot totals

What a measurement gives you

Every completed measurement produces the numbers an estimate needs, stored with the property so you can come back to them.

Measurement outputs and where they are used
OutputUsed for
Sloped roof area and squaresShingles, underlayment, tear-off and install labor
Pitch per planeSloped area, steep-slope labor and pitch-based pricing
Eaves and rakes (linear feet)Drip edge, starter strip and ice-and-water at the eaves
Ridges and hips (linear feet)Ridge cap and ridge vent
Valleys (linear feet)Valley metal or membrane
PenetrationsPipe boots, vents and flashing
Framed roof imageThe proposal the homeowner reviews and signs

From geometry to a usable estimate

Approved geometry can feed assemblies, waste factors, material quantities, price books, and proposal documents while preserving the source measurement.

Because the measurement stays attached to the estimate, a change to the roof (a missed dormer, a corrected pitch) can be carried through to quantities instead of being patched by hand in a spreadsheet.

Software or a per-report service?

If you measure a handful of roofs a year, buying a finished report per roof is simple. If you measure most of the roofs you bid, the per-report cost adds up and you lose the ability to edit what you were given.

Software plan prices are on the pricing page. For the full trade-off, including third-party report services, see the guides linked below.

Two ways to get roof measurements from MeasureRoofNow
Measure it yourselfOrder a report
Who traces the roofYou or your estimatorTraced and human-reviewed for you
Cost modelUnlimited self-service measurements on every paid software plan$19 per residential property (pilot)
Can you edit it?Yes, any timeYou receive a finished report
Feeds an estimate directlyYesEnter the numbers yourself

Know the limits

Satellite imagery may be old, incomplete, obstructed, misaligned, unavailable, or materially different from current site conditions. Trees, deep shadows and recent additions are the usual problems.

  • Treat every remote measurement as a planning figure
  • Verify on site before ordering material for a job you will be held to
  • Re-check pitch where shadows or overhangs hide the ridge line

Related guides and tools

Frequently asked questions

Does MeasureRoofNow automatically detect every roof?

No. The current production workflow is manual tracing with calculated geometry and human review.

Can I edit a measurement?

Yes. Roof planes and measurement details remain part of the property workflow for review and correction.

Can I order a report without subscribing?

Yes. A separate one-off human-reviewed residential report is available for $19 during the pilot.

Is there a limit on how many roofs I can measure?

No. Self-service measurements are unlimited on every paid software plan.

Where does the imagery come from?

From third-party satellite imagery providers. Provider attribution stays visible, and imagery date and quality vary by address.

Can I order material straight from a remote measurement?

Use it to bid and plan. For the final order on a job you have won, confirm the measurements on site, especially pitch and any additions the imagery may not show.